Hornbach Gateway Analyse

 Dieses mal zerlege ich einen Hornbach Smarthome Gateway und zeige euch alle Details, 

die ich dazu technisch finden konnte. 

Ziel dieses Projekts sollte sein die Firmware so zu modifizieren, dass ein lokales Webinterface

ohne die Hornbach-App möglich ist und weitere Geräte, die nicht integriert sind anzusprechen.

Starten wir mit ein paar Bildern: Hier zu sehen ist die Draufsicht des Gateways mit den Statusanzeigen für: 

Power 

Internet 

Wifi 

Z-Wave 

 Cloud 

Zigbee 

Bluetooth

  

In der Rückansicht sind ein LAN-Anschluss, Power und ein USB Port zu erkennen:

  

An der Gehäuseunterseite befindet sich die Seriennummer, die MAC-Addresse der LAN-Schnittstelle und der ID-Code, der für die Registrierung benötigt wird. 

(Wurde der ID-Code bereits bei einem anderen Hornbach Smarthome-Konto aktiviert, so kann dieser für eine weitere Person nicht hinzugefügt werden ehe der Vorbesitzer dieses Gateway aus seiner Smarthome-Konfiguration löscht oder ein Hornbach Support Mitarbeiter diesen Code aus dem Konto des Vorbesitzers löscht.) 

Zudem enthält das Gateway einen QR-Code, der die MAC-Addresse und den ID-Code als Text enthält: "m=MM:MM:MM:MM:MM:MM;ID=AB1-CDE"

Das Gehäuse lässt sich mit einem Schraubenzieher leicht öffnen. Nach dem öffnen den Deckel vorsichtig anheben, damit die Antennen nicht abreißen. Anschließend sieht das Innenleben wie folgt aus:

Im Netzwerk antwortet das Gerät nur auf einen Ping und es ist lt. NMap-Portscan kein offener Port zu finden. 

 Aus der Seriellen Konsole lassen sich im Standard folgende Information am UART-Port (57600 Baud, DataBits: 8, StopBits: 1) auslesen:

[0D]===================================================================

[0D]     [09][09]MT7621   stage1 code, 13:15:05 (ASIC)

[0D]     [09][09]CPU=50000000 HZ BUS=16666666 HZ

[0D]==================================================================

[0D]Change MPLL source from XTAL to CR...

[0D]do MEMPLL setting..

[0D]MEMPLL Config : 0x11100000

[0D]3PLL mode + External loopback

[0D]=== XTAL-40Mhz === DDR-1200Mhz ===

[0D]PLL4 FB_DL: 0x13, 1/0 = 703/321 4D000000

[0D]PLL2 FB_DL: 0x18, 1/0 = 591/433 61000000

[0D]PLL3 FB_DL: 0x18, 1/0 = 623/401 61000000

[0D]do DDR setting..[00320381]

[0D]Apply DDR3 Setting...(use customer AC)

[0D]          0    8   16   24   32   40   48   56   64   72   80   88   96  104  112  120

[0D]      --------------------------------------------------------------------------------

[0D]0000:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0001:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0002:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0003:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0004:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0005:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0006:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0007:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0008:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0009:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]000A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]000B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]000C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]000D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    1    1    1

[0D]000E:|    0    0    0    0    0    0    0    0    1    1    1    1    1    1    1    1

[0D]000F:|    0    0    0    1    1    1    1    1    1    1    1    1    0    0    0    0

[0D]0010:|    1    1    1    1    1    1    1    0    0    0    0    0    0    0    0    0

[0D]0011:|    1    1    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0012:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0013:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0014:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0015:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0016:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0017:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0018:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]0019:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]001A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]001B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]001C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]001D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]001E:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]001F:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0

[0D]rank 0 coarse = 15

[0D]rank 0 fine = 56

[0D]B:|    0    0    0    0    0    0    0    0    0    0    1    1    1    0    0    0

[0D]opt_dle value:11

[0D]DRAMC_R0DELDLY[018]=00001C1C

[0D]==================================================================

[0D][09][09]RX[09]DQS perbit delay software calibration 

[0D]==================================================================

[0D]1.0-15 bit dq delay value

[0D]==================================================================

[0D]bit|     0  1  2  3  4  5  6  7  8  9

[0D]--------------------------------------

[0D]0 |    11 7 13 9 13 7 13 5 3 11 

[0D]10 |    6 12 8 11 6 12 

[0D]--------------------------------------

[0D]

[0D]==================================================================

[0D]2.dqs window

[0D]x=pass dqs delay value (min~max)center 

[0D]y=0-7bit DQ of every group

[0D]input delay:DQS0 =28 DQS1 = 28

[0D]==================================================================

[0D]bit[09]DQS0[09] bit      DQS1

[0D]0  (1~53)27  8  (1~53)27

[0D]1  (1~50)25  9  (1~54)27

[0D]2  (1~55)28  10  (1~55)28

[0D]3  (1~55)28  11  (1~51)26

[0D]4  (1~55)28  12  (1~56)28

[0D]5  (1~53)27  13  (1~52)26

[0D]6  (1~54)27  14  (1~54)27

[0D]7  (1~56)28  15  (1~55)28

[0D]==================================================================

[0D]3.dq delay value last

[0D]==================================================================

[0D]bit|    0  1  2  3  4  5  6  7  8   9

[0D]--------------------------------------

[0D]0 |    12 10 13 9 13 8 14 5 4 12 

[0D]10 |    6 14 8 13 7 12 

[0D]==================================================================

[0D]==================================================================

[0D]     TX  perbyte calibration 

[0D]==================================================================

[0D]DQS loop = 15, cmp_err_1 = ffffba55 

[0D]DQS loop = 14, cmp_err_1 = ffff0a55 

[0D]DQS loop = 13, cmp_err_1 = ffff0a01 

[0D]DQS loop = 12, cmp_err_1 = ffff0001 

[0D]dqs_perbyte_dly.last_dqsdly_pass[1]=12,  finish count=1 

[0D]DQS loop = 11, cmp_err_1 = ffff0001 

[0D]DQS loop = 10, cmp_err_1 = ffff0000 

[0D]dqs_perbyte_dly.last_dqsdly_pass[0]=10,  finish count=2 

[0D]DQ loop=15, cmp_err_1 = ffff05aa

[0D]DQ loop=14, cmp_err_1 = ffff01aa

[0D]DQ loop=13, cmp_err_1 = ffff01aa

[0D]DQ loop=12, cmp_err_1 = ffff00aa

[0D]dqs_perbyte_dly.last_dqdly_pass[1]=12,  finish count=1 

[0D]DQ loop=11, cmp_err_1 = ffff0008

[0D]DQ loop=10, cmp_err_1 = ffff0000

[0D]dqs_perbyte_dly.last_dqdly_pass[0]=10,  finish count=2 

[0D]byte:0, (DQS,DQ)=(8,8)

[0D]byte:1, (DQS,DQ)=(8,8)

[0D]20,data:88

[0D][EMI] DRAMC calibration passed

[0D][0D]

[0D]===================================================================

[0D]     [09][09]MT7621   stage1 code done 

[0D]     [09][09]CPU=50000000 HZ BUS=16666666 HZ

[0D]===================================================================

[0D]U-Boot 1.1.3 (Oct 31 2018 - 16:51:14)[0A]

[0D]Board: Ralink APSoC DRAM:  256 MB

relocate_code Pointer at: 8ffac000[0A]

[0D]Config XHCI 40M PLL 

Allocate 16 byte aligned buffer: 8ffe0df0

Enable NFI Clock

# MTK NAND # : Use HW ECC

NAND ID [C2 F1 80 95 02]

Device not found, ID: c2f1

Not Support this Device! 

[0D]chip_mode=00000001

Support this Device in MTK table! c2f1 

[0D]select_chip

[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16

Signature matched and data read!

load_fact_bbt success 1023

load fact bbt success

[mtk_nand] probe successfully!

mtd->writesize=2048 mtd->oobsize=64,[09]mtd->erasesize=131072  devinfo.iowidth=8

Env addr : 0x80000

..============================================ 

Ralink UBoot Version: 4.2.1.0

-------------------------------------------- 

ASIC MT7621AS (MAC to MT7530 Mode)

DRAM_CONF_FROM: Auto-Detection 

DRAM_TYPE: DDR3 

DRAM bus: 16 bit

Xtal Mode=3 OCP Ratio=1/3

Flash component: NAND Flash

Date:Oct 31 2018  Time:16:51:14

============================================ 

icache: sets:256, ways:4, linesz:32 ,total:32768

dcache: sets:256, ways:4, linesz:32 ,total:32768 [0A]

[0D] ##### The CPU freq = 880 MHZ #### 

 estimate memory size =256 Mbytes[0A]

[0D]Reset switch ...

#Reset_MT7530[0A]

[0D]Please choose the operation: 

   1: Load system code to SDRAM via TFTP. 

   2: Load system code then write to Flash via TFTP. 

   3: Boot system code via Flash (default).

   4: Entr boot command line interface.

   9: Load Boot Loader code then write to Flash via TFTP. 

STANDALONE_LOAD_ADDR is 0xa0600000

..Example expects ABI version 2

Actual U-Boot ABI version 2[0A]

[0D][1B][31m******************************************

    Uboot StandAlone Entry

******************************************[1B][0m

0, cmd

1, 0x0000000D

cmd : 0x0000000D[0A]

[0D][08][08][08] 0 

Example expects ABI version 2

Actual U-Boot ABI version 2[0A]

[0D][1B][31m******************************************

    Uboot StandAlone Entry

******************************************[1B][0m

0, boot

Flash Sector Number : 522.

[0D][0D]***************************************************

[0D]    Sercomm Boot Version 2.00.1

[0D][0D]***************************************************

[0D]Entering Firmware : Everything is OK.

[0D]=================================================

Check image validation:

Image1 Header Magic Number --> OK

Image2 Header Magic Number --> Failed

Image1 Header Checksum --> OK

Image1 Data Checksum --> .......................OK[0A]

[0D]Image1: OK Image2: Broken

..Done![0A]

[0D]=================================================

..kernel addr :0xbfd40000 [0A]

[0D]flash base: 0xbfc00000, kernel addr :0xbfd40000, bootloader size: 0x80000, config size 0x80000, fac size : 0x40000

..Erasing NAND Flash...

.Writing to NAND Flash...

done

   

3: System Boot system code via Flash.

## Booting image at bfd40000 ...

   Image Name:   OpenWrt Linux-3.10.14

   Image Type:   MIPS Linux Kernel Image (lzma compressed)

   Data Size:    1477721 Bytes =  1.4 MB

   Load Address: 80001000

   Entry Point:  80001000

.......................   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK

No initrd

## Transferring control to Linux (at address 80001000) ...

## Giving linux memsize in MB, 256[0A]

[0D]Starting kernel ...[0A]

[0D]

LINUX started...

 THIS IS ASIC

SDK 5.0.S.0

[    0.000000] Linux version 3.10.14 (core3@ROCMAIN) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #18 SMP Fri Oct 30 11:04:49 UTC 2020

[    0.000000] 

[    0.000000]  The CPU feqenuce set to 880 MHz

[    0.000000] GCMP present

[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)

[    0.000000] Software DMA cache coherency

[    0.000000] Determined physical RAM map:

[    0.000000]  memory: 10000000 @ 00000000 (usable)

[    0.000000] Initrd not found or empty - disabling initrd

[    0.000000] Zone ranges:

[    0.000000]   DMA      [mem 0x00000000-0x0bffffff]

[    0.000000]   Normal   [mem 0x0c000000-0x0fffffff]

[    0.000000] Movable zone start for each node

[    0.000000] Early memory node ranges

[    0.000000]   node   0: [mem 0x00000000-0x0fffffff]

[    0.000000] avail: cpu2 is not ready

[    0.000000] avail: cpu3 is not ready

[    0.000000] Detected 1 available secondary CPU(s)

[    0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.

[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes

[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.

[    0.000000] PERCPU: Embedded 7 pages/cpu @8c204000 s6464 r8192 d14016 u32768

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024

[    0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 rootfstype=squashfs,jffs2

[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)

[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)

[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)

[    0.000000] Writing ErrCtl register=0002424b

[    0.000000] Readback ErrCtl register=0002424b

[    0.000000] Memory: 255284k/262144k available (3257k kernel code, 6860k reserved, 835k data, 252k init, 0k highmem)

[    0.000000] Hierarchical RCU implementation.

[    0.000000] [09]RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.

[    0.000000] NR_IRQS:128

[    0.000000] console [ttyS1] enabled

[    0.132000] Calibrating delay loop... 562.17 BogoMIPS (lpj=1124352)

[    0.164000] pid_max: default: 32768 minimum: 301

[    0.168000] Mount-cache hash table entries: 512

[    0.172000] launch: starting cpu1

[    0.176000] launch: cpu1 gone!

[    0.176000] CPU1 revision is: 0001992f (MIPS 1004Kc)

[    0.176000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.

[    0.176000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes

[    0.176000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.

[    0.208000] Synchronize counters for CPU 1: done.

[    0.216000] Brought up 2 CPUs

[    0.220000] NET: Registered protocol family 16

[    0.512000] release PCIe RST: RALINK_RSTCTRL = 7000000

[    0.516000] PCIE PHY initialize

[    0.520000] ***** Xtal 40MHz *****

[    0.524000] start MT7621 PCIe register access

[    1.100000] RALINK_RSTCTRL = 7000000

[    1.104000] RALINK_CLKCFG1 = 77ffeff8

[    1.108000] 

[    1.108000] *************** MT7621 PCIe RC mode *************

[    1.588000] PCIE0 no card, disable it(RST&CLK)

[    1.592000] pcie_link status = 0x6

[    1.596000] RALINK_RSTCTRL= 6000000

[    1.600000] *** Configure Device number setting of Virtual PCI-PCI bridge ***

[    1.604000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 10207f2

[    1.608000] PCIE1 enabled

[    1.612000] PCIE2 enabled

[    1.616000] interrupt enable status: 600000

[    1.620000] Port 1 N_FTS = 1b105000

[    1.624000] Port 0 N_FTS = 1b105000

[    1.628000] config reg done

[    1.632000] init_rt2880pci done

[    1.656000] bio: create slab <bio-0> at 0

[    1.660000] usbcore: registered new interface driver usbfs

[    1.664000] usbcore: registered new interface driver hub

[    1.668000] usbcore: registered new device driver usb

[    1.672000] PCI host bridge to bus 0000:00

[    1.676000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]

[    1.680000] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]

[    1.684000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

[    1.688000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring

[    1.704000] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring

[    1.720000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)

[    1.732000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)

[    1.748000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]

[    1.760000] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]

[    1.776000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]

[    1.788000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]

[    1.800000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]

[    1.816000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]

[    1.828000] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]

[    1.844000] pci 0000:00:00.0: PCI bridge to [bus 01]

[    1.852000] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]

[    1.868000] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]

[    1.880000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]

[    1.896000] pci 0000:00:01.0: PCI bridge to [bus 02]

[    1.904000] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]

[    1.920000] PCI: Enabling device 0000:00:00.0 (0004 -> 0006)

[    1.928000] PCI: Enabling device 0000:00:01.0 (0004 -> 0006)

[    1.940000] BAR0 at slot 0 = 0

[    1.948000] bus=0x0, slot = 0x0

[    1.952000] res[0]->start = 0

[    1.960000] res[0]->end = 0

[    1.964000] res[1]->start = 60300000

[    1.972000] res[1]->end = 6030ffff

[    1.980000] res[2]->start = 0

[    1.984000] res[2]->end = 0

[    1.988000] res[3]->start = 0

[    1.996000] res[3]->end = 0

[    2.000000] res[4]->start = 0

[    2.008000] res[4]->end = 0

[    2.012000] res[5]->start = 0

[    2.020000] res[5]->end = 0

[    2.024000] BAR0 at slot 1 = 0

[    2.028000] bus=0x0, slot = 0x1

[    2.036000] res[0]->start = 0

[    2.040000] res[0]->end = 0

[    2.048000] res[1]->start = 60310000

[    2.056000] res[1]->end = 6031ffff

[    2.060000] res[2]->start = 0

[    2.068000] res[2]->end = 0

[    2.072000] res[3]->start = 0

[    2.080000] res[3]->end = 0

[    2.084000] res[4]->start = 0

[    2.092000] res[4]->end = 0

[    2.096000] res[5]->start = 0

[    2.100000] res[5]->end = 0

[    2.108000] bus=0x1, slot = 0x0, irq=0x18

[    2.116000] res[0]->start = 60000000

[    2.124000] res[0]->end = 600fffff

[    2.128000] res[1]->start = 0

[    2.136000] res[1]->end = 0

[    2.140000] res[2]->start = 0

[    2.148000] res[2]->end = 0

[    2.152000] res[3]->start = 0

[    2.156000] res[3]->end = 0

[    2.164000] res[4]->start = 0

[    2.168000] res[4]->end = 0

[    2.176000] res[5]->start = 0

[    2.180000] res[5]->end = 0

[    2.184000] bus=0x2, slot = 0x1, irq=0x19

[    2.192000] res[0]->start = 60200000

[    2.200000] res[0]->end = 602fffff

[    2.208000] res[1]->start = 0

[    2.212000] res[1]->end = 0

[    2.220000] res[2]->start = 0

[    2.224000] res[2]->end = 0

[    2.232000] res[3]->start = 0

[    2.236000] res[3]->end = 0

[    2.240000] res[4]->start = 0

[    2.248000] res[4]->end = 0

[    2.252000] res[5]->start = 0

[    2.260000] res[5]->end = 0

[    2.264000] Bluetooth: Core ver 2.16

[    2.268000] NET: Registered protocol family 31

[    2.272000] Bluetooth: HCI device and connection manager initialized

[    2.276000] Bluetooth: HCI socket layer initialized

[    2.280000] Bluetooth: L2CAP socket layer initialized

[    2.284000] Bluetooth: SCO socket layer initialized

[    2.288000] Switching to clocksource MIPS

[    2.292000] NET: Registered protocol family 2

[    2.300000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)

[    2.316000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)

[    2.328000] TCP: Hash tables configured (established 2048 bind 2048)

[    2.340000] TCP: reno registered

[    2.348000] UDP hash table entries: 256 (order: 1, 8192 bytes)

[    2.360000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

[    2.372000] NET: Registered protocol family 1

[    2.468000] 4 CPUs re-calibrate udelay(lpj = 1167360)

[    2.480000] ======= sercomm_button_init =======

[    2.488000] mt7621_register_gpio_keys_polled start!

[    2.500000] mt7621_register_gpio_keys_polled ends!

[    2.512000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    2.524000] jffs2: version 2.2. (NAND) (SUMMARY)  (ZLIB) (LZO) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    2.544000] io scheduler noop registered (default)

[    2.556000] ======== sercomm_gpio_init ========

[    2.564000] ===== sercomm_gpio_ioctl_init =====

[    2.572000] ====== sercomm_led_ioctl_init =====

[    2.588000] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled

[    2.600000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A

[    2.616000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A

[    2.628000] serial8250: ttyS2 at MMIO 0x1e000e00 (irq = 28) is a 16550A

[    2.644000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error

[    2.656000] Allocate 16 byte aligned buffer: 80451d50

[    2.668000] Enable NFI Clock

[    2.672000] # MTK NAND # : Use HW ECC

[    2.680000] NAND ID [C2 F1 80 95 02, 00809502]

[    2.688000] Device not found, ID: c2f1

[    2.696000] Not Support this Device! [0D]

[    2.704000] chip_mode=00000001

[    2.712000] Support this Device in MTK table! c2f1 [0D]

[    2.720000] NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Macronix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64

[    2.744000] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16

[    2.756000] Scanning device for bad blocks

[    3.008000] Signature matched and data read!

[    3.016000] load_fact_bbt success 1023

[    3.024000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 

[    3.044000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 

[    3.064000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 

[    3.084000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 

[    3.104000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 

[    3.124000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 

[    3.144000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 

[    3.164000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 

[    3.184000] Creating 10 MTD partitions on "MT7621-NAND":

[    3.192000] 0x000000000000-0x000007f80000 : "ALL"

[    3.204000] 0x000000000000-0x000000080000 : "Bootloader"

[    3.216000] 0x000000080000-0x000000100000 : "Config"

[    3.228000] 0x000000100000-0x000000140000 : "Factory"

[    3.236000] 0x000000140000-0x000001540000 : "Firmware1"

[    3.252000] 0x0000002a8c99-0x000001540000 : "rootfs"

[    3.260000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only

[    3.296000] mtd: partition "rootfs_data" created automatically, ofs=0xa40000, len=0xb00000

[    3.312000] 0x000000a40000-0x000001540000 : "rootfs_data"

[    3.324000] 0x000001540000-0x000002940000 : "Firmware2"

[    3.336000] 0x000002940000-0x000002a40000 : "user_storage"

[    3.348000] 0x000002a40000-0x000003a40000 : "data"

[    3.360000] 0x000003a40000-0x000006c40000 : "storage"

[    3.368000] 0x000006c40000-0x000007f80000 : "backup"

[    3.380000] [mtk_nand] probe successfully!

[    3.388000] rootfs = 2a8c99 to a40000

[    3.396000] rdm_major = 253

[    3.404000] GMAC1_MAC_ADRH -- : 0x0000xxxx

[    3.412000] GMAC1_MAC_ADRL -- : 0xdeexxxx

[    3.420000] Ralink APSoC Ethernet Driver Initilization. v3.1  1024 rx/tx descriptors allocated, mtu = 1500!

[    3.440000] GMAC1_MAC_ADRH -- : 0x0000xxxx

[    3.448000] GMAC1_MAC_ADRL -- : 0xdeexxxx

[    3.456000] PROC INIT OK!

[    3.460000] *****run project phy.

[    3.476000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.492000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.508000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.524000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.540000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.556000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.572000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.588000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.604000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.620000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.652000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.668000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.684000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.700000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.716000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.732000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.748000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.764000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.780000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.796000] FM_OUT value: u4FmOut = 0(0x00000000)

[    3.924000] xhci-hcd xhci-hcd: xHCI Host Controller

[    3.932000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1

[    3.948000] xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000

[    3.960000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

[    3.972000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    3.988000] usb usb1: Product: xHCI Host Controller

[    3.996000] usb usb1: Manufacturer: Linux 3.10.14 xhci-hcd

[    4.008000] usb usb1: SerialNumber: xhci-hcd

[    4.016000] hub 1-0:1.0: USB hub found

[    4.024000] hub 1-0:1.0: 2 ports detected

[    4.032000] xhci-hcd xhci-hcd: xHCI Host Controller

[    4.044000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2

[    4.056000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003

[    4.072000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    4.084000] usb usb2: Product: xHCI Host Controller

[    4.096000] usb usb2: Manufacturer: Linux 3.10.14 xhci-hcd

[    4.104000] usb usb2: SerialNumber: xhci-hcd

[    4.116000] hub 2-0:1.0: USB hub found

[    4.120000] hub 2-0:1.0: 1 port detected

[    4.132000] usbcore: registered new interface driver usbserial

[    4.144000] usbcore: registered new interface driver usbserial_generic

[    4.156000] usbserial: USB Serial support registered for generic

[    4.168000] usbcore: registered new interface driver cp210x

[    4.180000] usbserial: USB Serial support registered for cp210x

[    4.192000] usbcore: registered new interface driver usb_debug

[    4.204000] usbserial: USB Serial support registered for debug

[    4.216000] usbcore: registered new interface driver ftdi_sio

[    4.228000] usbserial: USB Serial support registered for FTDI USB Serial Device

[    4.240000] usbcore: registered new interface driver pl2303

[    4.252000] usbserial: USB Serial support registered for pl2303

[    4.264000] TCP: cubic registered

[    4.272000] NET: Registered protocol family 10

[    4.280000] NET: Registered protocol family 17

[    4.292000] Bluetooth: RFCOMM TTY layer initialized

[    4.300000] Bluetooth: RFCOMM socket layer initialized

[    4.312000] Bluetooth: RFCOMM ver 1.11

[    4.320000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3

[    4.328000] Bluetooth: BNEP filters: protocol multicast

[    4.340000] Bluetooth: BNEP socket layer initialized

[    4.348000] 8021q: 802.1Q VLAN Support v1.8

[    4.364000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.

[    4.380000] Freeing unused kernel memory: 252K (80401000 - 80440000)

[    4.420000] usb 1-2: new high-speed USB device number 2 using xhci-hcd

[    4.452000] usb 1-2: New USB device found, idVendor=0e8d, idProduct=7662

[    4.464000] usb 1-2: New USB device strings: Mfr=4, Product=5, SerialNumber=6

[    4.480000] usb 1-2: Product: Wireless 

[    4.488000] usb 1-2: Manufacturer: MediaTek Inc.

[    4.496000] usb 1-2: SerialNumber: 000000000

[    4.504000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 3, maxp 16, interval 1, burst 0, mult 0, ep 0x8ff8ba80, ep_ctx 0xbbc10080, sch_ep 0x8f413e80

[    4.536000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x8ff8baac, ep_ctx 0xbbc100c0, sch_ep 0x8f413c00

[    4.564000] add_ep parameters, dev_speed 3, is_in 0, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x8ff8bad8, ep_ctx 0xbbc100a0, sch_ep 0x8f413980

[    4.592000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 1, maxp 0, interval 8, burst 0, mult 0, ep 0x8ffff280, ep_ctx 0xbbc10100, sch_ep 0x8f413780

[    4.620000] add_ep parameters, dev_speed 3, is_in 0, isTT 0, ep_type 1, maxp 0, interval 8, burst 0, mult 0, ep 0x8ffff2ac, ep_ctx 0xbbc100e0, sch_ep 0x8f413500

[    4.652000] 

[    4.652000] 

[    4.652000] Unsupported Device!

[    4.652000] Vendor=e8d ProdID=7662

[    4.652000] Manufacturer=MediaTek Inc. Product=Wireless 

[    4.652000] 

procd: Console is alive

[    5.992000] Button Hotplug driver version 0.4.1

[    6.024000] SCSI subsystem initialized

[    6.040000] usbcore: registered new interface driver usb-storage

procd: - preinit -

[    6.528000] 7F:FFFFFF8F:FFFFFFDF:FFFFFFE2:15:FFFFFF8B

[    6.540000] Raeth v3.1 (Tasklet)

[    6.552000] phy_free_head is 0x1bc1e000!!!

[    6.560000] phy_free_tail_phy is 0x1bc1fff0!!!

[    6.568000] txd_pool=bbc20000 phy_txd_pool=1BC20000

[    6.576000] ei_local->skb_free start address is 0x8fe8a6dc.

[    6.588000] free_txd: 1bc20010, ei_local->cpu_ptr: 1BC20000

[    6.600000]  POOL  HEAD_PTR | DMA_PTR | CPU_PTR 

[    6.608000] ----------------+---------+--------

[    6.620000]      0xbbc20000 0x1BC20000 0x1BC20000

[    6.628000] 

[    6.628000] phy_qrx_ring = 0x1bc07000, qrx_ring = 0xbbc07000

[    6.644000] 

[    6.644000] phy_rx_ring0 = 0x1bc28000, rx_ring0 = 0xbbc28000

[    6.680000] MT7530 Reset Completed!!

[    6.688000] change HW-TRAP to 0x17ccf

[    6.696000] set LAN/WAN LLLLW

[    6.708000] GMAC1_MAC_ADRH -- : 0x0000xxxx

[    6.716000] GMAC1_MAC_ADRL -- : 0xdeexxxx

[    6.728000] CDMA_CSG_CFG = 81000000

[    6.736000] GDMA1_FWD_CFG = 20710000

Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level

[    9.308000] block: attempting to load /etc/config/fstab

[    9.368000] block: extroot: not configured

jffs2 is ready

jffs2 is ready

[    9.472000] jffs2: Empty flash at 0x001a097c ends at 0x001a1000

[    9.640000] jffs2: notice: (329) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 12 of xref (0 dead, 1 orphan) found.

[   10.024000] block: attempting to load /etc/config/fstab

[   10.036000] block: ext

Die Fett markierten Bereiche werden im Laufe der Tage noch genauer getestet, ob hier eine

Serielle Konsole und der Debug über angeschlossene Tastatur aktiviert werden kann.

Diverse Kommandozeilenprogramme zur Verwendung in EvaCMD

Diverse Kommandozeilenprogramme zur Verwendung in EvaCMD

Details

Programmname	Beschreibung	Typ	Hersteller	Gruppe Anwendungsfall	Dateitypen	Link
Wscript	Windows Scripting Host	System(Default)	Microsoft	Interpreter	vbs, vbe
Mshta	Html Application	System(Default)	Microsoft	Interpreter	hta
cmd	Commandline	System(Default)	Microsoft	Interpreter	bat
Ping	Netzwerkerreichbarkeit	System(Default)	Microsoft	Netzwerk
Net	Netzwerktools	System(Default)	Microsoft	Netzwerk
Tracert	Netzwerkverfolgung	System(Default)	Microsoft	Netzwerk
Regedit	Systemregistrierung	System(Default)	Microsoft	Registrierung	reg
Arp	Adress Resolution Protokoll	System(Default)	Microsoft	Netzwerk
Attrib	Attribute	System(Default)	Microsoft	Dateisystem
Calcs	Dateirechte	System(Default)	Microsoft	Dateisystem
chkdsk	Festplattenüberprüfung	System(Default)	Microsoft	Dateisystem
Clip	Zwischenablage	System(Default)	Microsoft	Zwischenablage
Fsutil	Dateisystemaufgaben	System(Default)	Microsoft	Dateisystem
FTP	File Transfer	System(Default)	Microsoft	Netzwerk
gpUpdate	Group Policy Update	System(Default)	Microsoft	Gruppenrichtlinien
gpResult	Group Policy Results	System(Default)	Microsoft	Gruppenrichtlinien
gpScript	Group Policy Script	System(Default)	Microsoft	Gruppenrichtlinien
NetSh?	Netzwerkshell	System(Default)	Microsoft	Netzwerk
NetStat?	Netzwerkstatus	System(Default)	Microsoft	Netzwerk
PathPing?		System(Default)	Microsoft	Netzwerk
RasDial?	Anwahl über Modem	System(Default)	Microsoft	Netzwerk
Runas	Ausführen als Benutzer X	System(Default)	Microsoft	Rechte
Services	Dienste	System(Default)	Microsoft	Dienste
SFC	System File Checker	System(Default)	Microsoft	Dateisystem
Shutdown	Herunterfahren, Neustarten	System(Default)	Microsoft	System
Systeminfo	Systeminformationen	System(Default)	Microsoft	System
TakeOwn?	Besizerrechte übernehmen	System(Default)	Microsoft	Dateisystem
Taskkill	Tasks beenden	System(Default)	Microsoft	Tasks
Tasklist	Tasks auflisten	System(Default)	Microsoft	Tasks
TaskEng?	TaskPlanungsprogramm?	System(Default)	Microsoft	Geplante Tasks
Xcopy	Dateien kopieren	System(Default)	Microsoft	Dateisystem
wmic	WMI Management Console	System(Default)	Microsoft	System
Dir	Verzeichnisinhalt	System(Default)	Microsoft	Dateisystem
Tree	Verzeichnisstuktur	System(Default)	Microsoft	Dateisystem
Set	Umgebungsvariablen	System(Default)	Microsoft	System
Robocopy	Dateien kopieren	System(Additional)	Microsoft	Dateisystem
Xcacls	Dateirechte	System(Additional)	Microsoft	Dateisystem
Icalcs	Dateirechte	System(Additional)	Microsoft	Dateisystem
AccessChk?		System(Additional)	Sysinternals
AccessEnum?		System(Additional)	Sysinternals
AdExplorer?		System(Additional)	Sysinternals
AdInsight?		System(Additional)	Sysinternals
AdRestore?		System(Additional)	Sysinternals
Autologon		System(Additional)	Sysinternals
Autoruns		System(Additional)	Sysinternals
BgInfo?		System(Additional)	Sysinternals
CacheSet?		System(Additional)	Sysinternals
ClockRes?		System(Additional)	Sysinternals
Contig		System(Additional)	Sysinternals
Coreinfo		System(Additional)	Sysinternals
Ctrl2Cap?		System(Additional)	Sysinternals
DebugView?		System(Additional)	Sysinternals
Desktops		System(Additional)	Sysinternals
Disk2vhd		System(Additional)	Sysinternals
DiskExt?		System(Additional)	Sysinternals
DiskMon?		System(Additional)	Sysinternals
DiskView?		System(Additional)	Sysinternals
Disk Usage (DU)		System(Additional)	Sysinternals
EFSDump		System(Additional)	Sysinternals
FindLinks?		System(Additional)	Sysinternals
Handle		System(Additional)	Sysinternals
Hex2dec		System(Additional)	Sysinternals
Junction		System(Additional)	Sysinternals
LDMDump		System(Additional)	Sysinternals
ListDLLs		System(Additional)	Sysinternals
LiveKd?		System(Additional)	Sysinternals
LoadOrder?		System(Additional)	Sysinternals
LogonSessions?		System(Additional)	Sysinternals
MoveFile?		System(Additional)	Sysinternals
NTFSInfo		System(Additional)	Sysinternals
PageDefrag?		System(Additional)	Sysinternals
PendMoves?		System(Additional)	Sysinternals
PipeList?		System(Additional)	Sysinternals
PortMon?		System(Additional)	Sysinternals
ProcDump?		System(Additional)	Sysinternals
Process Explorer		System(Additional)	Sysinternals
Process Monitor		System(Additional)	Sysinternals
PsExec?		System(Additional)	Sysinternals
PsFile?		System(Additional)	Sysinternals
PsGetSid?		System(Additional)	Sysinternals
PsInfo?		System(Additional)	Sysinternals
PsPing?		System(Additional)	Sysinternals
PsKill?		System(Additional)	Sysinternals
PsList?		System(Additional)	Sysinternals
PsLoggedOn?		System(Additional)	Sysinternals
PsLogList?		System(Additional)	Sysinternals
PsPasswd?		System(Additional)	Sysinternals
PsService?		System(Additional)	Sysinternals
PsShutdown?		System(Additional)	Sysinternals
PsSuspend?		System(Additional)	Sysinternals
RAMMap		System(Additional)	Sysinternals
RegDelNull?		System(Additional)	Sysinternals
Registry Usage (RU)		System(Additional)	Sysinternals
RegJump?		System(Additional)	Sysinternals
RootkitRevealer?		System(Additional)	Sysinternals
SDelete		System(Additional)	Sysinternals
ShareEnum?		System(Additional)	Sysinternals
ShellRunas?		System(Additional)	Sysinternals
SigCheck?		System(Additional)	Sysinternals
Streams		System(Additional)	Sysinternals
Strings		System(Additional)	Sysinternals
Sync		System(Additional)	Sysinternals
TCPView		System(Additional)	Sysinternals
VMMap		System(Additional)	Sysinternals
VolumeID		System(Additional)	Sysinternals
WhoIs?		System(Additional)	Sysinternals
WinObj?		System(Additional)	Sysinternals
ZoomIt?		System(Additional)	Sysinternals
R	Programmiersprache R	Programm	R	Interpreter	R
Scilab	Programmiersprache Scilab	Programm	Scilab	Interpreter	scl
Perl	Programmiersprache Perl	Programm	Perl	Interpreter	perl
Python	Programmiersprache Python	Programm	Python	Interpreter	py,pyc
LUA	Programmiersprache LUA	Programm	LUA	Interpreter	lua
PHP	Programmiersprache PHP	Programm	PHP	Interpreter	php
Java	Programmiersprache Java	Programm	Oracle	Interpreter	Jar
Ruby	Programmiersprache Ruby	Programm	Ruby	Interpreter
XULRunner	Programmiersprache XUL	Programm	Mozilla	Interpreter	xul
AutoItx?	Programmiersprache Autoitx	Programm	AutoItx?	Interpreter, System	atx
7Zip	Komprimierung	Programm	Igor Pavlov	Komprimierung	zip, rar, tar, gz
GraphWiz?	Grafische Darstellungen	Programm	Graphwiz	Grafik	dot
XMLStarlet	XML bearbeiten	Programm		Text	xml
FSK166	Multifunktion	Programm		System
Node.js	Programmiersprache Javascript	Programm	Node.js	Interpreter, Netzwerk	vbs
Curl	Netzwerkanfragen	Programm		Netzwerk
Wget	Netzwerkanfragen	Programm		Netzwerk
ffmpeg	Videobearbeitung	Programm	ffmpeg	Multimedia	avi, mpeg, mpg, mp3, mp2, ogg
ffplay	Video abspielprogramm	Programm	ffmpeg	Multimedia	avi, mpeg, mpg, mp3, mp2, ogg
ffprobe	Video Testprogramm	Programm	ffmpeg	Multimedia	avi, mpeg, mpg, mp3, mp2, ogg
Sendemail	Mail Senden	Programm		Netzwerk, Mail
blat	Mail Senden	Programm		Netzwerk, Mail
nmap	Netzwerkgeräte auflisten	Programm		Netzwerk
netcat (ncat)	Netzwerktoolkit	Programm		Netzwerk
AutoHotKey?	Tastenkombinationen	Programm		System
snmp	Simply Network Management	Programm		Netzwerk, SNMP
espeak	Sprachausgabe (klingt hölzern)	Programm		Sprachausgabe
wol	Wake on Lan	Programm		Netzwerk
nircmd	Multifunktion	Programm		System
sleep	Pause für x Sekunden	Programm		System
sox	Audio bearbeitung	Programm		Audio	mp3, ogg
tail	Dateiänderung überwachen	Programm		Text	txt, csv
Julius	Spracherkennung	Programm		Spracherkennung
CMU Sphinx	Spracherkennung	Programm		Spracherkennung
GoogleCL	Google Dienste	Programm	Google	Netzwerk
Fping	Netzwerkverfügbarkeit	Programm		Netzwerk
Adb	Android	Programm	Google
Fastboot	Android	Programm	Google
Snort	Netzwerk, IDS	Programm	Snort
Windump	Netzwerkmitschnitt	Programm	TCPDump
AdinRec?	Audio	Programm			wav
DevCon?	Gerätemanager	Programm	Microsoft
Enhancer	Audio	Programm			mp3, ogg
Exiv2	Bilder	Programm			jpeg
Fciv	Prüfsummen	Programm
Gzip	Komprimierung	Programm			zip
SQLite3	Datenbank	Programm	SQLite
Qemu	System Emulator	Programm			img, bin
WSusOffline	Windows Updates (Paket)	Programm
PDFTK	PDF Toolkit	Programm
Nuget	Versionierung	Programm	NuGet?
Git	Versionierung	Programm	Git
SVN	Versionierung	Programm	SVN
neolog	Logging	Programm
nginx	Webserver	Programm	Nginx		html
sox	Sound Tool	Programm			mp3, ogg
wavpack	Sound Tool	Programm			wav
Tesseract	Texterkennung	Programm	Tesseract		jpg
IsoInfo?	Informationen über ISO Images	Programm			iso
Mod_Key?	Überwacht Systemereignisse	Deamon	NBHCREW
Mod_Apache?	Webserver	Deamon	NBHCREW
Mod_T4e?	Lieder auf Techno4Ever?	Deamon	NBHCREW
Mod_Serial?	Serielle Kommunikation	Deamon	NBHCREW
Mod_Faststart?	Dateiindizierung	Deamon	NBHCREW
Mod_Sprachausgabe2?	Sprachausgabe über Google	Deamon	NBHCREW
Mod_Wingui?	Bedieninterface	Deamon	NBHCREW
Mod_Webserver?	Webserver	Deamon	NBHCREW
Mod_SSH	Secure Shell	Deamon	NBHCREW
Mod_Tinkerforge?	Kommuniziert mit Tinkerforge	Deamon	NBHCREW
Mod_Notices?	Notizzettel	Programm	NBHCREW
Mod_Messages?	Nachrichtenausgabe	Programm	NBHCREW
Mod_Sprachausgabe?	Sprachausgabe über Google	Programm	NBHCREW
Mod_Spracherkennung?	Spracherkennung über Google	Programm	NBHCREW
Mod_Spracherkennung2?	Spracherkennung über WinSapi?	Programm	NBHCREW
Mod_Spracherkennung3?	Spracherkennung über CMU Sphinx	Programm	NBHCREW
Wget2	Netzwerkanfragen	Programm	NBHCREW
Mod_Show?	Webbrowser	Programm	NBHCREW
GoogleMail?	Mails	Programm	NBHCREW
Mod_RSS	Rss-Feeds	Programm	NBHCREW
Mod_Twitter?	Twitter Nachrichten	Programm	NBHCREW
Mod_Facebook?	Facebook Nachrichten	Programm	NBHCREW
Mod_TV	Tv-Programm	Programm	NBHCREW
Mod_Wetter?	Wetterdaten	Programm	NBHCREW
Mod_YesNo?	Benutzereingabe	Programm	NBHCREW
Mod_SPDNS	Updated die IP über SPDNS	Programm	NBHCREW
Mod_Events?	Überwacht Systemereignisse	VB-Script	NBHCREW
Piep	Gibt ein Piepen aus	VB-Script	NBHCREW
Input	Benutzereingabe	VB-Script	NBHCREW
JaNein?	Benutzereingabe	VB-Script	NBHCREW
Studierstube	Audio, Video, Augemented Reality	Programmpaket			avi, mpeg, mpg, mp3, mp2, ogg
Tex	Dokumente	Programmpaket	MikTex?		Tex
Gimp	Grafik	Programmpaket	Gimp
Metasploit	Pentest Programme	Programmpaket
GNU CoreUtils?	Unix-Tools für Windows	Programmpaket	GNU			http://www.gnu.org/software/coreutils/manual/coreutils.html?
UNXUtils	Unix-Tools für Windows 2	Programmpaket	GNU			http://unxutils.sourceforge.net/?
Wireshark	Netzwerkmitschnitt (CMD-Interface)	Programm(GUI)			dmp
VLC	Media Player (Mit Kommandozeilenparametern)	Programm(GUI)			avi, mpeg, mpg, mp3, mp2, ogg	https://wiki.videolan.org/Documentation:Command_line/?
Google.de	Websuche, Sprache, Informationen	Website(REST)
WolframAlpha?	Informationen	Website(REST)
Youtube.com	Videos	Website(Parse)
TVToday.de	Fernsehprogramme	Website(Parse)
Twitter	Nachrichten	Website(REST)
Facebook	Nachrichten	Website(REST)
Jdownloader	Downloader	Webinterface	Jdownloader
VLC	MediaPlayer?	Webinterface	VLC
FHEM	Heimautomatisierung	Webinterface	FHEM
TVHeadend	TV-Streaming	Webinterface	LonelyCoder?
XBMC	Mediacenter	Webinterface	XBMC
Motion	Kameraaktionen	Webinterface	Motion
Lua	Programmiersprache	Library			lua
Log4Net?	Logger	Library
FireBall?	Code-Editor	Library			html, xml, txt, csv
Gecko16	Webbrowser	Library			html, js, mml, xml, jpg, gif
Json	Json Verarbeitung	Library			json
HTML AgilityPack?	HTML Verarbeitung	Library			html
PDFSharp	Pdf Verarbeitung	Library			pdf
Ionic Zip	Zip	Library			zip
ZedGraph?	Kennlinien, Graphen	Library
SQLite	Datenbank	Library
OpenJDK	Java in .Net	Library			jar
Saxon	XML-Interpreter	Library			xml
Interop.Excel	Excel Interoperabilität	Library			xls
Interop.VBA	VBA Interoperabilität	Library			vba
AutoITX	Automatisierung	Library			au
Ncalc	Mathematische Ausdrücke	Library
MathJax?	Darstellung von MathMl?	Webservice			mml
Blockly	Grafische Programmierumgebung	Webservice
Dojo	Grafische Darstellung	JavaScript?-Bibliothek
Jquery	Grafische Darstellung	JavaScript?-Bibliothek